Dio breakout - Revision history

Cartridge1987 at 12:06, 10 December 2015

2015-12-10T12:06:06Z

Cartridge1987: /* Pinout */

2015-12-09T15:08:00Z

Pinout

Rew: /* Future hardware enhancements */

2013-05-17T13:24:09Z

Future hardware enhancements

Rew: /* configurations */

2013-05-17T13:22:54Z

configurations

Rew: /* jumper settings */

2013-05-17T13:22:45Z

jumper settings

Rew: /* Additional software */

2013-05-17T13:20:17Z

Additional software

Rew: /* External resources */

2013-05-17T13:20:09Z

External resources

Rew: /* Datasheets */

2013-05-17T13:19:58Z

Datasheets

Rew: /* Pinout */

2013-05-17T13:19:41Z

Pinout

Rew: Created page with "The DIO breakout board. This is the documentation page for the DIO_breakout . == Overview == This board en..."

2013-05-17T13:18:24Z

Created page with "thumb|300px|alt=The DIO breakout board|The DIO breakout board. This is the documentation page for the DIO_breakout . == Overview == This board en..."

New page

[[File:DIO_breakout.jpg|thumb|300px|alt=The DIO breakout board|The DIO breakout board.]]

This is the documentation page for the DIO_breakout .

== Overview ==

This board enables use screw terminals to connect wires to your SPI_DIO or I2C_DIO board.

== Assembly instructions ==

None: the board comes fully assembled.

== External resources ==

=== Datasheets ===

== Additional software ==

=== Related projects ===

[[DIO]]

== Pinout ==

{| border=1
! pin !! function
|-
| 1 || GND
|-
| 2 || IO0
|-
| 3 || IO1
|-
| 4 || IO2
|-
| 5 || IO3
|-
| 6 || IO4
|-
| 7 || IO5
|-
| 8 || IO6
|}

{| border=1
! pin !! function
|-
| 1 || GND
|-
| 2 || VCC
|-
| 3 || GND
|-
| 4 || VCC
|-
| 5 || GND
|-
| 6 || VCC
|-
| 7 || GND
|-
| 8 || VCC
|}

== jumper settings ==

There are no jumpers.

== Future hardware enhancements ==

== Future software enhancements ==

== Changelog ==

=== 1.0 ===
* Initial public release

@@ Line 90: / Line 90: @@
 d.n.c. means do not connect.
-== jumper settings ==
+== Jumper settings ==
 There are no jumpers.
-== configurations ==
+== Configurations ==
 You can chose to have your board equipped with a 10-pin female connector that allows your board to directly fit on top of the I2C-DIO board. This would conflict with the SPI connectors so don't chose this option for an SPI_DIO.

@@ Line 87: / Line 87: @@
 | 10 || IO6
 |}
+d.n.c. means do not connect.
 == jumper settings ==

← Older revision		Revision as of 13:22, 17 May 2013
Line 95:		Line 95:

	You can chose to have your board equipped with a 10-pin female connector that allows your board to directly fit on top of the I2C-DIO board. This would conflict with the SPI connectors so don't chose this option for an SPI_DIO.		You can chose to have your board equipped with a 10-pin female connector that allows your board to directly fit on top of the I2C-DIO board. This would conflict with the SPI connectors so don't chose this option for an SPI_DIO.

	You can chose to have your board equipped with a male 10-pin connector that allows you to connect your board with the SPI_DIO or I2C DIO using a short 10pin IDC cable.		You can chose to have your board equipped with a male 10-pin connector that allows you to connect your board with the SPI_DIO or I2C DIO using a short 10pin IDC cable.

@@ Line 90: / Line 90: @@
 == jumper settings ==
 There are no jumpers.
+== configurations ==
+You can chose to have your board equipped with a 10-pin female connector that allows your board to directly fit on top of the I2C-DIO board. This would conflict with the SPI connectors so don't chose this option for an SPI_DIO.
+You can chose to have your board equipped with a male 10-pin connector that allows you to connect your board with the SPI_DIO or I2C DIO using a short 10pin IDC cable.
 == Future hardware enhancements ==

← Older revision		Revision as of 13:20, 17 May 2013
Line 10:		Line 10:

	None: the board comes fully assembled.		None: the board comes fully assembled.

	== Additional software ==

@@ Line 100: / Line 100: @@
 == Future hardware enhancements ==
+may 2013: This is vaporware: hardware will be available june 2013.
 == Future software enhancements ==

@@ Line 10: / Line 10: @@
 None: the board comes fully assembled.
-== External resources ==
 == Additional software ==

← Older revision		Revision as of 13:19, 17 May 2013
Line 12:		Line 12:

	== External resources ==		== External resources ==


	=== Datasheets ===

@@ Line 27: / Line 27: @@
+The connector at the bottom of the board is laid out as follows:
 {| border=1
 ! pin !! function
@@ Line 47: / Line 48: @@
 |}
+the power-connector at the top of the board is laid out as follows:
 {| border=1
@@ Line 68: / Line 71: @@
 |}
+The dataconnector in the middle of the board is compatible with the DIO board:
+{| border=1
+! pin !! function
+|-
+| 1 || GND
+|-
+| 2 || VCC
+|-
+| 3 || IO0
+|-
+| 4 || IO1
+|-
+| 5 || IO2
+|-
+| 6 || IO3
+|-
+| 7 || d.n.c.
+|-
+| 8 || IO4
+|-
+| 9 || IO5
+|-
+| 10 || IO6
+|}
 == jumper settings ==